มีบริการอุปกรณ์สำรองระหว่างซ่อมและ Onsite Services ตลอด 24 ชั่วโมง 365 วัน (ข้อมูลเพิ่มเติม คลิก...)

Cisco Catalyst 9100 | C9120AXE-S Cisco Catalyst 9120AXE Access Point, external antennas

SKU: C9120AXE-S
Band: Cisco
Type: Wireless Access Point
Model: Catalyst 9100
Part Number: C9120AXE-S
Features: Embedded Wireless Controller / Lightweight AP
Detail:
Cisco Catalyst 9120AXE Access Point, external antennas
฿35,999.00 ราคายังไม่รวมภาษีมูลค่าเพิ่ม.
Cisco
รายละเอียดสินค้า
รายละเอียด

 Features and benefits

Feature

Benefits

Wi-Fi 6 (802.11ax)

The IEEE 802.11ax emerging standard, also known as High-Efficiency-Wireless (HEW) or Wi-Fi 6, builds on 802.11ac. It delivers a better experience in typical environments with more predictable performance for advanced applications such as 4K or 8K video, high-density, high-definition collaboration apps, all-wireless offices, and IoT. Wi-Fi 6 is designed to use both the 2.4-GHz and 5-GHz bands, unlike the 802.11ac standard.

Cisco RF ASIC

Cisco RF ASIC is a fully integrated Software-Defined Radio (SDR) that can perform advanced RF spectrum analysis and delivers features like Cisco CleanAir®, Wireless Intrusion Prevention System (wIPS), Fast Locate*, and DFS detection.

(*Future)

Uplink/downlink OFDMA

Orthogonal Frequency-Division Multiple Access (OFDMA)-based scheduling splits the bandwidth into smaller chunks called Resource Units (RUs), which can be allocated to individual clients in both the downlink and uplink directions to reduce overhead and latency.

MU‑MIMO technology

Supporting four spatial streams, Multiuser Multiple Input, Multiple Output (MU-MIMO) enables access points to split spatial streams between client devices, to maximize throughput.

BSS coloring

Spatial reuse (also known as Basic Service Set [BSS] coloring) allows the access points and their clients to differentiate between BSSs, thus permitting more simultaneous transmissions.

Target wake time

A new power savings mode called Target Wake Time (TWT) allows the client to stay asleep and to wake up only at prescheduled (target) times to exchange data with the access point. This offers significant energy savings for battery-operated devices, up to three to four times greater compared to 802.11n and 802.11ac.

Intelligent Capture

Intelligent Capture probes the network and provides Cisco DNA Center with deep analysis. The software can track over 240 anomalies and instantaneously review all packets on demand, emulating the onsite network administrator. Intelligent Capture allows for more informed decisions on your wireless networks.

Flexible Radio Assignment

Allows the access points to intelligently determine the operating mode of serving radios based on the RF environment. The access points can operate in the following modes:

  2.4-GHz and 5-GHz mode: One radio will serve clients in 2.4-GHz mode, while the other serves clients in 5-GHz mode.
  Dual 5-GHz mode: Both radios inside the access point operate on the 5-GHz band, maximizing the benefits of Wi-Fi 6 and increasing client device capacity.

Dual 5-GHz radio support

Enables both radios to operate in 5-GHz client serving mode, allowing an industry-leading 5.2 Gbps (2 x 2.6 Gbps) over-the-air speeds while increasing client capacity.

Smart antenna connector

An intelligent second physical antenna connector is included on 9120AX Series access points with an external antenna. This connector provides advanced network design flexibility for high-density and large open-area environments such as auditoriums, convention centers, libraries, cafeterias, and arenas/stadiums, allowing two sets of antennas to be connected and active on a single access point.

Cisco Embedded Wireless Controller

The 9120AX Series Wi-Fi 6 access points is available with a built-in controller. The Cisco Embedded Wireless Controller on Catalyst 9100 Access Points provides an easy-to-deploy and manage option that does not require a physical appliance. The control resides on the access point so there is no added footprint or complexity. And, because it uses Cisco Catalyst 9800 Series code, it’s easy to migrate your network as your needs grow.

Application Hosting on Catalyst 9100 Access

Application Hosting on Catalyst 9100 Access Points helps future-proof and simplify IoT deployments by eliminating the need to install and manage overlay networks. Utilizing the USB interface, containerized applications and hardware modules can be deployed to reduce cost and complexity. Adding Cisco DNA Center provides workflows and deployment-wide application lifecycle management.

Multigigabit Ethernet support

Provides uplink speeds of 2.5 Gbps, in addition to 100 Mbps and 1 Gbps. All speeds are supported on Category 5e cabling for an industry first, as well as 10GBASE-T (IEEE 802.3bz) cabling.

Bluetooth® radio

Integrated Bluetooth Low Energy 5 radio to enable IoT use cases such as location tracking and wayfinding.

Container support for applications

Enables edge computing capabilities for IoT applications on the host access point.

Apple features

Apple and Cisco have partnered to create an optimal mobile experience for iOS devices on corporate networks based on Cisco technologies. Using new features in iOS 10, in combination with the latest software and hardware from Cisco, businesses can now more effectively use their network infrastructure to deliver an enhanced user experience across all business applications.

At the center of the collaboration is a unique handshake between the Cisco WLAN and Apple devices. This handshake enables the Cisco WLAN to provide an optimal Wi-Fi roaming experience to Apple devices. Additionally, the Cisco WLAN trusts Apple devices and gives priority treatment for business-critical applications specified by the Apple device. This feature is also known as Fast Lane.

Secure infrastructure

Trustworthy systems built with Cisco Trust Anchor Technologies provide a highly secure foundation for Cisco products. With the Cisco Catalyst 9100 Access Points, these technologies enable hardware and software authenticity assurance for supply chain trust and strong mitigation against man-in-the-middle attacks that compromise software and firmware. Trust Anchor capabilities include:

      Image signing

      Secure Boot

      Cisco Trust Anchor module

Cisco DNA support

Pairing the Cisco Catalyst 9120AX Series Access Points with Cisco DNA allows for a total network transformation. Cisco DNA allows you to truly understand your network with real-time analytics, quickly detect and contain security threats, and easily provide networkwide consistency through automation and virtualization. The 9120AX Series supports Software-Defined Access (SD-Access), Cisco’s leading enterprise architecture.

Working together, the Cisco Catalyst 9120AX Series and Cisco DNA offer such features as:

      Cisco DNA Spaces

      Cisco Identity Services Engine

      Cisco DNA Analytics and Assurance

Product specifications

Item

Specification

Part numbers

Cisco Catalyst 9120AXI Access Point: Indoor environments, with internal antennas

  C9120AXI-x: Cisco Catalyst 9120AX Series

Cisco Catalyst 9120AXE Access Point: Indoor, challenging environments, with external antennas

  C9120AXE-x: Cisco Catalyst 9120AX Series

Cisco Catalyst 9120AXP Access Point: Indoor, professional installations

  C9120AXP-x: Cisco Catalyst 9120AX Series

Cisco Catalyst 9120AXI Access Point: Indoor environments, with internal antennas, with embedded wireless controller

  C9120AXI-EWC-S: Cisco Catalyst 9120AX Series

Cisco Catalyst 9120AXE Access Point: Indoor, challenging environments, with external antennas, with embedded wireless controller

  C9120AXE-EWC-S: Cisco Catalyst 9120AX Series

Cisco Catalyst 9120AXP Access Point: Indoor, professional installations, with embedded wireless controller

  C9120AXP-EWC-S: Cisco Catalyst 9120AX Series

Regulatory domains: (S = Thailand domain)

Software

  Cisco Unified Wireless Network Software Release 8.9.x or later
  Cisco IOS XE Software Release 16.11 with AP Device Pack, or later

Supported wireless LAN controllers

  Cisco Catalyst 9800 Series Wireless Controllers
  Cisco 3500, 5520, and 8540 Series Wireless Controllers and Cisco Virtual Wireless Controller

802.11n version 2.0 (and related) capabilities

  4x4 MIMO with four spatial streams
  Maximal Ratio Combining (MRC)
  802.11n and 802.11a/g beamforming
  20- and 40-MHz channels
  PHY data rates up to 890 Mbps (40 MHz with 5 GHz and 20 MHz with 2.4 GHz)
  Packet aggregation: A-MPDU (transmit and receive), A-MSDU (transmit and receive)
  802.11 Dynamic Frequency Selection (DFS)
  Cyclic Shift Diversity (CSD) support

802.11ac

  4x4 downlink MU-MIMO with four spatial streams
  MRC
  802.11ac beamforming
  20-, 40-, 80-, and 160-MHz channels
  PHY data rates up to 3.47 Gbps (160 MHz with 5 GHz)
  Packet aggregation: A-MPDU (transmit and receive), A-MSDU (transmit and receive)
  802.11 DFS
  CSD support

802.11ax

  4x4 downlink MU-MIMO with four spatial streams
  Uplink/downlink OFDMA
  TWT
  BSS coloring
  MRC
  802.11ax beamforming
  20-, 40-, 80-, and 160-MHz channels
  PHY data rates up to 5.38 Gbps (160 MHz with 5 GHz and 20 MHz with 2.4 GHz)
  Packet aggregation: A-MPDU (transmit and receive), A-MSDU (transmit and receive)
  802.11 DFS
  CSD support

Integrated antenna

Flexible radio (either on 2.4 GHz or on 5 GHz)

  2.4 GHz, peak gain 4 dBi, internal antenna, omnidirectional in azimuth
  5 GHz, peak gain 5 dBi, internal antenna, omnidirectional in azimuth

Dedicated 5-GHz radio

  5 GHz, peak gain 5 dBi, internal antenna, omnidirectional in azimuth

External antenna (sold separately)

  Cisco Catalyst 9120AXE Access Points are certified for use with antenna gains up to 6 dBi (2.4 GHz and 5 GHz)
  Cisco Catalyst 9120AXP Access Points) are certified for use with antenna gains up to 13 dBi (2.4 GHz and 5 GHz) with the AIR-ANT2513P4M-N= antenna
  Supports Self-Identifiable Antennas (SIA) on one RP-TNC port

Smart antenna connector

  Available on the 9120AXE and 9120AXP only
  Compact multi-RF connector with DART interface
  Requires the AIR-CAB002-DART-R= 2 ft smart antenna connector when used with antennas with RP-TNC connector
  Required when running the flexible radio as either a second 5-GHz serving radio or a Wireless Security Monitoring radio

Interfaces

  1x 100, 1000, 2500  Multigigabit Ethernet (RJ-45) – IEEE 802.3bz
●  Auto-MDIX support
  Management console port (RJ-45)
  USB 2.0 @ 4.5W

Indicators

  Status LED indicates boot loader status, association status, operating status, boot loader warnings, and boot loader errors

Dimensions
(W x L x H)

  Access point (without mounting brackets): C9120AXI: 8.5 x 8.5 x 1.7” (21.6 x 21.6 x 4.3 cm), C9120AXE and C9120AXP: 8.5 x 8.05 x 2.0” (21.6 x 21.6 x 5.1 cm)

Weight

Cisco Catalyst 9120AXI

  2.87 lb (1.3 kg)

Cisco Catalyst 9120AXE/P

  3 lb (1.36 kg)

Input power requirements

  802.3at Power over Ethernet Plus (PoE+), 802.3bt Cisco Universal PoE (Cisco UPOE+, Cisco UPOE)
  802.3af PoE
  Cisco power injector, AIR-PWRINJ6= (Note: This injector supports only 802.3at)
  Cisco power injector, AIR-PWRINJ5= (Note: This injector supports only 802.3af)

Power draw

Catalyst 9120AXI

PoE power consumption

2.4-GHz radio

5-GHz radio

Link speed

USB

LLDP

802.3at (PoE+)

4x4

4x4

2.5G

Y

25.5W

Catalyst 9120AXE, 9120AXP

PoE power consumption

2.4-GHz radio

5-GHz radio

Link speed

USB

LLDP

802.3at (PoE+)

4x4

4x4

2.5G

Y

25.5W

Catalyst 9120AXI, 9120AXE, 9120AXP

PoE power consumption

2.4-GHz radio

5-GHz radio

Link speed

USB

LLDP

802.3af

PoE

1x1

1x1

1G

N

13.4W

802.3af

PoE

2x2

N

1G

N

13.4W

802.3af

PoE

N

2x2

1G

N

13.4W

 

Note: Power required at the Power Source Equipment (PSE) will depend on the cable length and other environmental issues

Environmental

Cisco Catalyst 9120AXI

  Nonoperating (storage) temperature: -22° to 158°F (-30° to 70°C)
  Nonoperating (storage) altitude test: 25˚C, 15,000 ft.
  Operating temperature: 32° to 122°F (0° to 50°C)
  Operating humidity: 10% to 90% (noncondensing)
  Operating altitude test: 40˚C, 9843 ft.

Note: When the ambient operating temperature exceeds 40°C, the access point will shift from 4x4 to 2x2 on both the 2.4-GHz and 5-GHz radios, uplink Ethernet will downgrade to 1 Gigabit Ethernet; however, the USB interface will remain enabled

Cisco Catalyst 9120AXE and 9120AXP

  Nonoperating (storage) temperature: -22° to 158°F (-30° to 70°C)
  Nonoperating (storage) altitude test: 25˚C, 15,000 ft.
  Operating temperature: -4° to 122°F (-20° to 50°C)
  Operating humidity: 10% to 90% (noncondensing)
  Operating altitude test: 40˚C, 9843 ft.

System memory

  2048 MB DRAM
  1024 MB flash

Warranty

Limited lifetime hardware warranty

Available transmit power settings

2.4 GHz

  23 dBm (200 mW)
  -4dBm(0.39mW)

5 GHz

  23 dBm (200 mW)
  -4dBm (0.39mW)

Compliance standards

  Safety:

    IEC 60950-1

    EN 60950-1

    UL 60950-1

    CAN/CSA-C22.2 No. 60950-1

    AS/NZS 60950-1

    UL 2043

    Class III equipment

  Emissions:

    CISPR 32 (rev. 2015)

    EN 55032 (rev. 2012/AC:2013)

    EN 55032 (rev. 2015)

    EN 55035 2010

    EN61000-3-2 (rev. 2014)

    EN61000-3-3 (rev. 2013)

    KN61000-3-2

    KN61000-3-3

    AS/NZS CISPR 32 Class B (rev. 2015)

    47 CFR FCC Part 15B

    ICES-003 (rev. 2016 Issue 6, Class B)

    VCCI-CISPR 32:2016

    VCCI (V3)

    CNS (rev. 13438)

    KN-32

    KN-35

    KN 301 489-17

    TCVN 7189 (rev. 2009)

  Immunity:

    CISPR 24 (rev. 2010)

    EN 55024 / EN 55035 (rev. 2010)

  Emissions and immunity:

    EN 301 489-1 (v2.1.1 2017-02)

    EN 301 489-17 (v3.1.1 2017-02)

    QCVN (18:2014)

    KN 489-1

    KN 489-17

    EN 60601 (1-1:2015)

  Radio:

    EN 300 328 (v2.1.1)

    EN 301 893 (v2.1.1)

    AS/NZS 4268 (rev. 2017)

    47 CFR FCC Part 15C, 15.247, 15.407

    RSP-100

    RSS-GEN

    RSS-247

    China regulations SRRC

    LP0002 (rev 2018.1.10)

    Japan Std. 33a, Std. 66, and Std. 71

  RF safety:

    EN 50385 (rev. Aug 2002)

    ARPANSA

    AS/NZS 2772 (rev. 2016)

    EN 62209-1 (rev. 2016)

    EN 62209-2 (rev. 2010)

    47 CFR Part 1.1310 and 2.1091

    RSS-102

  IEEE standards:

    IEEE 802.3

    IEEE 802.3ab

    IEEE 802.3af/at

    IEEE 802.11 a/b/g/n/ac/ax

    IEEE 802.11h, 802.11d

  Security:

    802.11i, Wi-Fi Protected Access 3 (WPA3), WPA2, WPA

    802.1X

    Advanced Encryption Standard (AES)

  Extensible Authentication Protocol (EAP) types:

    EAP-Transport Layer Security (TLS)

    EAP-Tunneled TLS (TTLS) or Microsoft Challenge Handshake Authentication Protocol Version 2 (MSCHAPv2)

    Protected EAP (PEAP) v0 or EAP-MSCHAPv2

    EAP-Flexible Authentication via Secure Tunneling (EAP-FAST)

    PEAP v1 or EAP-Generic Token Card (GTC)

    EAP-Subscriber Identity Module (SIM)

 

Cisco Catalyst 9120i - 2.4 GHz Antenna Patterns

 

Cisco Catalyst 9120i - 5 GHz Antenna Patterns

 

Cisco Catalyst 9120i - 5 GHz Antenna Patterns

 

Cisco Catalyst 9120i -  RF ASIC Antenna

 

Related image, diagram or screenshot

Figure 1.  Antenna radiation patterns

Warranty information

The Cisco Catalyst 9120AX Series Access Points come with a limited lifetime warranty that provides full warranty coverage of the hardware for as long as the original end user continues to own or use the product. The warranty includes 10-day advance hardware replacement and ensures that software media are defect-free for 90 days.

ข้อมูลเพิ่มเติม
ข้อมูลเพิ่มเติม
ประเภท Wireless Access Point
Model Catalyst 9100
License / Features Embedded Wireless Controller / Lightweight AP
รีวิวสินค้า
เขียนรีวิวสินค้าของคุณเอง
คุณกำลังรีวิว: Cisco Catalyst 9100 | C9120AXE-S Cisco Catalyst 9120AXE Access Point, external antennas
คุณจะให้คะแนนสินค้านี้อย่างไร? *
  1 ดาว 2 ดาว 3 ดาว 4 ดาว 5 ดาว
บริการ
ราคา